Maintenance Materials For Industry
Phone: 800.321.9300
Fax: 800.441.9303
Local Phone: 216.475.8000
Local Fax: 216.475.6067
Linkedin
Manta

Tool & Die Steels

RHINO-DIE™ - Pre-Hardened, High Performance Die Steel

Why Choose Rhino-Die?

Rhino-Die is similar to a 4330 alloy. It is made to Clean Steel Production Technology. Rhino-Die provides excellent dimensional stability and is field proven in the following type dies; zinc, aluminum, plastic and rubber molds, and for forming all types of sheet metal. It will accept many forms of surface conditioning, including flame and induction hardening, carbide coating, PVD and nitriding.

Rhino-Die should be considered as a replacement for; 4130, 4140, 4145, 4340, H-13, and P-20. When starting with an annealed alloy you are required to rough machine, then heat treat, then straighten, and finally finish machine the die. This is costly and prone to rework. Many times the die will need to be completely remade, resulting in expensive time lost.

Rhino-Die is a pre-hardened high performance die steel that comes to you ready to machine and put into service. It is simple and quick and it does the job.

Consider the following...

If you are quoting a job, you will be quoting against competitors who are still using annealed tool steels. The added cost will be reflected in their quote to your customer.

Your lead time will be one quarter of the time they require to complete that manufacturing sequence. Your bid will be lower; your lead time will be faster.

Longer Tool Life
Less Downtime
Increased Productivity
Cost Effective

Key Features

• Delivered "Pre-Hardened" Approx. Rockwell "C" 42
• Excellent Impact Strength
• Excellent Etching and Polishing
• Excellent Machinability Characteristics
• Dimensionally Stable Up To 800°F
• Low Carbon Equivalency (CE)
• Thermal Fatigue Resistance - Similar To Hot Work Die Steels

Independent Testing (as tested)

Hardness 422/450 BHN
Tensile Strength
(Per ASTM E8-08, ASTM A370-08a)
  207/229 KSI
Yield Strength   180 KSI
Elongation   13% - 16.5%
Reduction of Area   48% - 53%
Impact/LCVN   Av. 21ft/lbs @ +73°F

Clean Steel Production Process

Electric Furnace Melt, Vacuum Degassed, Grain Fine, Low Sulfur, Low Phosphorus, Inclusion Shape Control, Material produced under certified quality management system ISO 9001 ABS-QE Cert #30130.

Typical Applications

  • Zinc Dies
  • Rubber Molds
  • Brass Pressing Dies
  • Hot & Cold Forging Dies
  • Extrusion Dies
  • Aluminum Die Cast Molds
  • Shearing Dies

General Fabrication Data

Machining: The hardness is furnished at approximately 42Rc, so standard precautions observed for machining hardened alloys prevail. (The chemistry is very similar to a 4330 alloy). Use equipment of sufficient capacity to avoid chatter and vibration. Machine operators should be familiar with machining hardened alloys and tool steels. Increase pressure – decrease speed to avoid glazing. (Glazing is similar to flame or surface hardening of the immediate work area.)

Rhino-Die is a through-hardened alloy, which means you should not encounter the hard and soft spots typically found in commercial grade steels.

Drilling: Cobalt or carbide drills are excellent resources but not required. Hardened twist drills, or High Speed (M-2 type) drills should be adequate. Flood with generous coolant, (20% soluble oil). Use heavy capacity high quality equipment to minimize chatter and vibration. Increase feed and lower speed to avoid "glazing". Where possible, use a hand feed as opposed to a power feed. Power feeds tend to over-power and create small chips which may lodge, or jam. Hand feed allows greater control and "feel" to maintain a scraping type of motion, (long chip). We suggest use of a pilot hole, then follow-up with a reamer type of action. "Dubb", or dull, the edge on the second drill to create a scraping motion, as opposed to a cutting action. For cobalt alloyed high speed tools (example: overcarburized M42), utilize tools with a tapered shank and long helical short bit. Flood with lubricant – 20% diluted soluble oil. Where multiple holes are required you may want to consider tungsten carbide tipped tooling, or solid carbide tools. (ISO K-10 or K-20).

Drill bit preparation: Grind away the metal behind the lip to obtain clearance. (10° is preferred). Most drill failures, that occur when drilling hard plate, are along the land, not at the entry point. Thin the point significantly at the entry point.

For additional information contact our Cleveland office.

Size Availability

Please enquire as to availability.

We stock large master plates that can be cut to your requirements. We utilize high definition plasma cutting equipment to give you clean, close tolerance (laser quality) edges, on thicknesses up to 1-1/2". Top and bottom plate surfaces are hot rolled to hot rolled tolerances. Blanchard and finish grinding services are available.

View our online catalog for PDF brochures on these and other products.

Customer SurveyBetter Business Bureau

© Associated Steel Corporation      E-mail: mail@associatedsteel.com      Powered by Dynamics Online, Inc.